Jun 15, 2020. #1. Ducato Maxi 130 multijet 2013. I had to reset the time, because the battery had been disconected. When I next started the vehicle the airbag light and the passenger airbag deactivated lights where glowing as well as the mileage display is flashing. I looked in the manual and found that you can deactivate the passenger airbag 13. Sep 16, 2015. #1. I have a 55 plate Fiat Croma 1.9 150 Multijet with new DPF its done 120.000 miles and i keep getting Fault light on. I have a Snap on Various (Usless) and i get code P2002 and limp mode. tried regen holding 4th at 70 MPH 3000Rpm it won't regen for 1/2 hour. I'm seriously thinking on Taking it off and putting straight bit Hi all, I’m a total newbie and I stumbled across this forum through google and I’m glad I did. I’m looking for some help please regards the OBD on the new Fiat Ducato. First of all the OBD located in the small panel o the drivers side isn’t like any I’ve seen before, instead of being the usual

Fiat Ducato – fuse box diagram – Main fuse box under the dashboard on the driver’s side for the right-hand drive version, on the passenger’s side for the right-hand drive version. Right rear position light. Left rear position light. License plate lighting. Electric mirrors.

1. Location. France. May 27, 2023. #5. It seems that SGW appeared on 24/02/2019 on Serie6 (Fiat code 6Y, nuovo ducato euro6d). Indeed the modification number 23582, changes the glove box drawer. On new Ducato (Series 7c, ducato FCA 2021), It is possible that the SGW is integrated to BCM. Last edited: May 28, 2023.
Mar 20, 2015. #1. I saw a recent post answered by ECUNOTEMU regarding an obd android ELM 27TH interface with demo alfa obd android app. Can anybody (or ecunotmu ) advise if this set up will work on the earlier 244 JTD series Ducato engine? I know that this engine isn't strictly OBD2 compliant but uses the ISO9141-2 protocol which is supported
I'm hoping that I'm not the only control freak that would like to know when the ECU initiates a DPF regeneration / burn routine on my Fiat Ducato 130bhp Multijet (2014) Euro 5 engine. I'm running the Torque app, with OBD2 Wifi adapter, but the only available control panel values aren't really of any help. It can monitor the EGR position, but
Mid 70's. Apr 2, 2021. #15. Took the mh for it's first ride out in six months on 1st April, airbag fault warning light stayed on. No chance the cause was low battery, as some have reported, as solar and ehu kept the battery's in good nick over winter. Checked all connections under both cab seats, they seem ok. Location of components: CFB block - located on the left side of the dashboard on the driver's side (or on the passenger side on right-hand drive models). To gain access to the fuses, unscrew the two fixing screws (A). CFO block - located on the right side of the dashboard on the passenger side (or on the driver's side on right-hand drive models Peugeot Boxer 2.8 HDI / Fiat Ducato JTD 2001 OBD Fault Code Reading and Clearing with Creader VIII / 123This engine does NOT use ODBII instead it has a 3-pin Two factors will show if your vehicle is definitely OBD II equipped: 1) There will be an OBD II connector as shown. 2) There will be a note on a sticker or nameplate under the hood: "OBD II compliant". The SAE J1962 specification provides for two standardized hardware interfaces, called type A and type B. Both are female, 16-pin (2x8), D-shaped .
  • 34u7c9qt9m.pages.dev/248
  • 34u7c9qt9m.pages.dev/197
  • 34u7c9qt9m.pages.dev/209
  • 34u7c9qt9m.pages.dev/136
  • 34u7c9qt9m.pages.dev/228
  • 34u7c9qt9m.pages.dev/306
  • 34u7c9qt9m.pages.dev/492
  • 34u7c9qt9m.pages.dev/94

    • fiat ducato 2002 obd location